"Thank you Kent for the directions on rewiring the tuning eye. Worked like a charm!"
The Fine Things are Always Hand Made
KIM L BOWERS's Page
Latest Activity
IMG_3103
"OK...sorry, storms here last night ook out power and were very distracting.
Looking at what you have, the red wire is the B+ to the plate (250V) and the wire beside it will be the grid, so those are the two most critical to get right. Two of…"
IMG_3103
""The orange/red wire attached to a lug that one end of the resistor is soldered to. Next to it is tan with green tracer still attached.""
"The orange/red wire attached to a lug that one end of the resistor is soldered to. Next to it is tan with green tracer still attached."
IMG_3103
"First...we can figure this out, it isn't hard. Next...that 1 Meg resistor inside the socket - now is the perfect time to replace it. They have always shifted high in value and reduce the eye action a lot. Putting in a new 1M resistor will…"
IMG_3103
"Well now I did it. While opening the socket for the tuning eye I manages to pull loose three of the five wires. Couldn't have left well enough alone as it was working. There are only two wires still attached to the…"
"which 2 knobs? the several control shafts? the "S" walnut or the brown bakelite?"
"There is a link at the top of the site: "Scott Info Archive". Go there, then select the "Set Folders" and find the "Super XII" folder.
Kent"
Top view of chassis
"Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which location signifies a Super 12.
The two additional control shafts…"
"At 8:41pm on February 2, 2024, David C. Poland said…
Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which…"
"At 8:41pm on February 2, 2024, David C. Poland said…
Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which…"
"Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which location signifies a Super 12.
The two additional control shafts…"
KIM L BOWERS's Photos
Comment Wall (3 comments)
- At 11:52am on February 3, 2024,
David C. Poland said…
At 8:41pm on February 2, 2024,
Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which location signifies a Super 12.
The two additional control shafts were indeed a late version enhancement of early 1940, just before the introduction of the Scott 14 tube Masterpiece which moved the output tubes to a larger 3 tube power supply. I had such a 6 control Super 12 with the 2 additional controls, but never got to a restoration.
Accordingly, I suspect your one tube outboard power supply should have the upgraded 5U4 rectifier (rather than a 5V4) as per a one page addendum to the instruction manual. Do your tube sockets have embossed tube numbers?
Per the addendum, the two additional controls are:
lower left: radio/phono switch
Lower right: Sensitivity.
If so, the radio phono switch was moved away from the band switch to accommodate the optional 5th band: the ultra high TV audio red band mine had.
Looks to me like your receiver chassis is missing the left rear corner coil assembly. But the two adjustment hole covers on the left middle coil can look like the early version Super 12 when the power transformer was located on the receiver left rear corner. So maybe yours is complete.
Remember, Scott was a custom set builder. Perhaps used parts on hand (older version middle can) to build yours near the end of the Super 12 production.
HAVING site trouble - this comment may appear gain
- At 11:51am on February 3, 2024,
At 8:41pm on February 2, 2024,
Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which location signifies a Super 12.
The two additional control shafts were indeed a late version enhancement of early 1940, just before the introduction of the Scott 14 tube Masterpiece which moved the output tubes to a larger 3 tube power supply. I had such a 6 control Super 12 with the 2 additional controls, but never got to a restoration.
Accordingly, I suspect your one tube outboard power supply should have the upgraded 5U4 rectifier (rather than a 5V4) as per a one page addendum to the instruction manual. Do your tube sockets have embossed tube numbers?
Per the addendum, the two additional controls are:
lower left: radio/phono switch
Lower right: Sensitivity.
If so, the radio phono switch was moved away from the band switch to accommodate the optional 5th band: the ultra high TV audio red band mine had.
Looks to me like your receiver chassis is missing the left rear corner coil assembly. But the two adjustment hole covers on the left middle coil can look like the early version Super 12 when the power transformer was located on the receiver left rear corner. So maybe yours is complete.
Remember, Scott was a custom set builder. Perhaps used parts on hand (older version middle can) to build yours near the end of the Super 12 production.
- At 8:41pm on February 2, 2024,
Kim - welcome to the Scott Enthusiasts web site.
Just to be clear, your receiver should have the pair of 6V6 output tubes at the rear in the middle behind the tuning cap cover, which location signifies a Super 12.
The two additional control shafts were indeed a late version enhancement of early 1940, just before the introduction of the Scott 14 tube Masterpiece which moved the output tubes to a larger 3 tube power supply. I had such a 6 control Super 12 with the 2 additional controls, but never got to a restoration.
Accordingly, I suspect your one tube outboard power supply should have the upgraded 5U4 rectifier (rather than a 5V4) as per a one page addendum to the instruction manual. Do your tube sockets have embossed tube numbers?
Per the addendum, the two additional controls are:
lower left: radio/phono switch
Lower right: Sensitivity.
If so, the radio phono switch was moved away from the band switch to accommodate the optional 5th band: the ultra high TV audio red band mine had.
Looks to me like your receiver chassis is missing the left rear corner coil assembly. But the two adjustment hole covers on the left middle coil can look like the early version Super 12 when the power transformer was located on the receiver left rear corner. So maybe yours is complete.
Remember, Scott was a custom set builder. Perhaps used parts on hand (older version middle can) to build yours near the end of the Super 12 production.
© 2024 Created by Kent King.
Powered by
